Related Links
Evaluation of Cu nano particles addition on the vertical density profile and mechanical properties of medium density fiberboard (MDF) | ||
| تحقیقات علوم چوب و کاغذ ایران | ||
| Article 3, Volume 29, Fall 3 - Serial Number 48, November 2014, Pages 368-375 PDF (709.42 K) | ||
| Document Type: Research Paper | ||
| DOI: 10.22092/ijwpr.2014.6133 | ||
| Authors | ||
| Aliakbar Aenayati* 1; Halimeh Pangh2; Mahammad Layeghi3; Kazem Doosthosseini4 | ||
| 1- Professor, Dept. of Wood and Paper Science and technology, University of Tehran | ||
| 2M.Sc, wood and Paper Science and technology, University of Tehran | ||
| 3Assistant Professor, Dept. of Wood and Paper Science and technology, University of Tehran | ||
| 4Professor, Dept. of Wood and Paper Science and technology, University of Tehran | ||
| Abstract | ||
| This study was conducted to investigate the effect of Cu nano particles addition on the density profile and mechanical properties of medium density fiberboard. One layer fiberboard (MDF) with the density of 0.58g/cm3and thickness of 17 mm were produced using Cu nano particles in three levels (5, 10 and 15wt%based on solid content of resin) and urea formaldehyde resin content in two levels (8 and 10wt%based on oven dry weight of fibers) as variable factors. The control panels were produced using 10% resin (based on oven dry weight of fibers) without Cu nano particles using the identical manufacturing parameters as other panels. Mechanical strength including internal bonding (lB), bending strength, modulus of elasticity and density profile using slicing method were determined. The results indicated that increasing the content of Cu nano-particles had no significant effect on the internal bonding as well as bending strength and modulus of elasticity of panels. Increasing the resin content from 8 to 10 percent improved modulus of elasticity (43.7%), bending strength (18.9%) and internal bonding (23%) of panels. In addition, the increasing Cu nano particles up to 5% caused relatively higher IB for panels produced using 8%resin compared to the control panels(containing10% resin) as well as the density profile was more uniform with the lowest differences between maximum and minimum density in the density profile. | ||
| Keywords | ||
| MEDIUM DENSITY FIBERBOARD; Cu nano-particles. Density profile; MECHANICAL PROPERTIES | ||
| References | ||
|
-Ee Ding Wong, Min Zhang, Qian Wang, Guangping Han, Shuichi Kawai. 2000. Formation of the density profile and its effects on the properties of fiberboard. J Wood Sci (2000) 46:202-209. -Farajollah pour, M. and Dosthosseini, K., 2010. Effects of copper and silver nanoparticles on thermal conductivity and mechanical and physical properties of particleboard pressing cycle, the master's thesis. Tehran University. -Geng, X. , Deng, J. , Zhang, S.Y., 2006. Effects of hot-pressing parameters and wax content on the properties of fiberboard made from paper mill sludge. Volume 38, Issue 4, October 2006, Pages 736-741. -Habibi, M., Hosseinkhani, H. And Mahdavi, S. 2007. Investigate the effect of press time and resin content on the properties of medium density fiberboard (MDF) made from rice straw, Iranian Journal of Wood and Paper Science, 22 (1): 61-51, p. -Kargarfard, A., Dosthosseini, K., Jahan-Ltybary, A. and Hossein-Zadeh, A., 2003. Effect of temperature and pressing time on heat transfer in particleboard manufacturing process. Research and development (16), pp. 56-62. -Nourbakhsh, A. And Kargarfard, A., 2005. Effect of press time and amount of glue particleboard made from a mixture of lignocellulosic resources in southern Iran, Iranian Journal Wood and Paper Science, 20 (1): 64 - 47 p. -Siqun Wang, Paul M. Winistorfer, Timothy M. Young, 2004, Fundamentals of vertical density profile formation in wood composites.partIII. MDF density formation during hot- pressing. Tennessee Forest Products Center, Wood and Fiber Science, 36(1), pages: 17–25. -Torrey, K.S., Yrjana, W.A., King, J.A. 2003. Effect of thermally conductive fillers on the internal bond strength of strandboard. Volume 53, Issue 11-12, November 2003, Pages 74-80 -Wang, S. & Winistorfer, P. M. 2000. “Fundamentals of vertical density profile formation in wood composites.Part II. Methodology of vertical density formation under dynamic conditions.” Wood and Fiber Science, 32, 220-238. -Yosephi, H., Enayati, A.A., Faezipour, M.M. and Sadatnejad, S., 2008. Effect of steaming time and resin content on the properties of medium density fiberboard (MDF) made from stems colza, Iranian Journal of wood and Paper Science, 23 (1): 156-149, | ||
|
Statistics Article View: 3,415 PDF Download: 1,490 |
||
Journal management system. designed by sinaweb