| تعداد نشریات | 286 |
| تعداد نشریات سازمان | 84 |
| تعداد شماره‌ها | 3,007 |
| تعداد مقالات | 33,647 |
| تعداد مشاهده مقاله | 44,618,213 |
| تعداد دریافت فایل اصل مقاله | 33,444,532 |
بررسی آزمایشگاهی و عددی تاثیر پیشروی انسداد بر آبشستگی در پایین‌دست کالورت جعبه‌ای | ||
| تحقیقات مهندسی سازه های آبیاری و زهکشی | ||
| دوره 26، بهار - شماره پیاپی 98، اردیبهشت 1404، صفحه 104-85 اصل مقاله (987.01 K) | ||
| نوع مقاله: مقاله پژوهشی | ||
| شناسه دیجیتال (DOI): 10.22092/idser.2025.369299.1617 | ||
| نویسندگان | ||
| رضا باوندپوری گیلان1؛ رسول قبادیان* 2؛ علی آرمان1 | ||
| 1گروه مهندسی آب، دانشکده کشاورزی، پردیس کشاورزی و منابع طبیعی، دانشگاه رازی، کرمانشاه، ایران. | ||
| 2گروه مهندسی آب، پردیس کشاورزی و منابع طبیعی، دانشگاه رازی، کرمانشاه، ایران. | ||
| چکیده | ||
| کالورت‌ها سازه‌های هیدرولیکی هستند که در تقاطع مجرای آب با جاده و موانع به کار می‌روند. انسداد کالورت از عوامل مهم کاهش کارایی و تخریب آن است. تاثیر انسداد با پیشروی در مجرای اصلی کالورت تشدید می‌یابد. پیشروی انسداد موجب ایجاد تغییرات اساسی در هیدرولیک جریان و به دنبال آن تغییر در آبشستگی پایین‌دست نسبت به حالت بدون انسداد می‌شود. در این تحقیق، تاثیر پیشروی انسداد بر آبشستگی در پایین‌دست کالورت جعبه‌ای به صورت آزمایشگاهی بررسی شد، موضوعی که در تحقیقات پیشین بررسی نشده است. به منظور شناسایی دقیق‌تر الگوی جریان، به‌ویژه در طول مجرای کالورت و اندرکنش جریان و رسوب در پایین‌دست، شبیه‌سازی عددی با نرم‌افزار FLOW-3D بهانجام رسید. آزمایش‌ها در سه شدت دبی 0/45، 0/83 و 1/24؛ چهار عمق پایاب نسبی 0/47، 1/37، 2/17 و 3/07 و سه پیشروی انسداد صفر، 0/32L و 0/5L به اجرا درآمدند که در آن L طول مجرای کالورت است. نتایج موید وابستگی عمق آبشستگی به پیشروی انسداد، شدت دبی و عمق پایاب می‌باشد. در غیاب انسداد، وجود یک عمق پایاب نسبی بحرانی، ابتدا باعث کاهش و سپس افزایش عمق آبشستگی در پایین‌دست می‌شود. بررسی نتایج در حالت انسداد 32 درصد سطح مقطع ورودی در دو پیشروی 32 و 50 درصد انسداد در مجرای کالورت نشان داد که با افزایش عمق پایاب تاثیر پیشروی انسداد بر عمق آبشستگی ناچیز می‌شود، به طوری که در عمق پایاب نسبی 3/07، مقدار حداکثر عمق آبشستگی پایین‌دست در سه حالت بدون انسداد و انسداد با پیشروی‌های 32 و 50 درصد، تفاوت چندانی ندارند. یافته‌های تحقیق حاضر می‌تواند راهکارهای مناسبی برای کنترل آبشستگی در پایین‌دست کالورت در برابر انسداد و پیشروی آن به طراحان ارائه دهد. | ||
| کلیدواژه‌ها | ||
| آبشستگی؛ انسداد ورودی؛ بررسی آزمایشگاهی؛ کالورت؛ مدل عددی | ||
| عنوان مقاله [English] | ||
| Experimental and numerical investigation of the effect of blockage progression on scour downstream of box culvert | ||
| نویسندگان [English] | ||
| Reza Bavandpoori Gilan1؛ Rasool Ghobadian2؛ Ali Arman1 | ||
| 1Department of Water Engineering. Faculty of Agriculture. Campus of Agriculture and Natural Resources, Razi University. Kermanshah, iran. | ||
| 2Water Engineering Department. Campus of Agriculture and Natural Resources. Razi University. Kermanshah.Iran | ||
| چکیده [English] | ||
| Introduction Blockage in the culvert is a major factor in reducing its efficiency. The effect of culvert blockage intensifies by progress in the barrel. This study investigated the effect of blockage progression on scour downstream of box culvert using experimental tests, which hasn’t been investigated in previous research. In order to more accurately identify the flow pattern, especially along the culvert channel and the interaction of flow and sediment downstream, numerical simulations were performed with FLOW-3D software. The findings can aid engineers in considering the effects of scour and blockage in the design of more efficient culverts. Methodology Using the modeling of natural phenomena in a laboratory environment, we can understand the behavior of a phenomenon in a real environment. The planned experiments were conducted in the Hydraulic Laboratory of the Water Sciences and Engineering Department at Razi University. The width, depth, and length of the flume are 0.50 m, 0.60 m, and 5.40 m, respectively. The culvert, with a length of 30 cm and a rectangular cross-section measuring 10 cm in width and 7.50 cm in height, is made of glass with a thickness of 8 mm. To ensure developed flow upon entering the culvert, it is positioned 3.60 m from the beginning of the flume. At the inlet and outlet of the culvert, a type 2 USBR transition with equal angles of convergence and divergence of 26.50 degrees is used. To control the downstream water level at the desired level, a sharp-crested weir with variable height is installed downstream of the culvert. the floor of the flume upstream of the structure is uniformly covered with concrete, and the downstream section is filled by uniform sediment with diameter of 0.85 mm and thickness of 20 cm. A total of 36 experiment were conducted with three flow rate of 2.95, 5.38 and 8.03 L/s, four downstream depth of 4.5, 10.3, 16.3 and 23 cm with three blockage scenarios 0, 0.2L and 0.32L where L is the barrel length. After reaching equilibrium in each experiment, the height of the installed weir was increased to prevent a rapid drop in water level, then the pump was turned off. After complete drainage, bed changes were recorded using a 3D scanner equipped with a Kinect camera, which had an accuracy of ±0.2 mm. The data extracted from the camera was then prepared for plotting the necessary graphs. Finally, the bed surface was carefully leveled for the next experiment. Results and Discussion Based on the comparison of experimental and numerical results, it was determined that the numerical model has sufficient ability to simulate the water surface and its results are reliable. Regarding sedimentary results, comparison of the results test Q2 yt3 α32 β32 by both experimental and numerical methods showed the formation of a scour hole immediately after the end of the outlet transition and the creation of a sedimentation mound after the hole. Investigation of the effect of relative tailwater depth on scour depth in unblocked conditions showed that at a fixed relative tailwater depth, the dimensionless maximum scour depth increases with the increasing flow intensity parameter. Specifically, as the flow intensity increases from 0.45 to 1.24 at a constant tailwater depth, the flow velocity inside the culvert barrel increases, and consequently, water exits the culvert downstream with greater velocity. This increase in velocity at a fixed tailwater depth leads to higher shear stress on the bed and enhanced flow power in sediment transport and bed erosion. Regarding the effect of the progression of blockage in the culvert barrel on scour at the outlet, it can be said that when the inlet section of the culvert is blocked, the maximum scour depth downstream of the culvert decreases. The reason for this is that, in the case of fixed blockage, an eddy flow with a horizontal axis is created just behind the obstruction, causing the streamlines separate and resulting in intense turbulence in the channel, in such a way that the flow hits the culvert roof several times and then dives back toward the channel floor. This process leads to significant energy loss in the flow, reducing the flow's potential for downstream scour compared to the unblocked condition. Conclusions progression of the blockage in the culvert barrel can affect the flow hydraulic within it and has notable impacts on the scour of the downstream bed. Due to the impossibility of measuring some parameters, such as the Maximum scour hole depth at desired times in the laboratory environment due to high flow turbulence, the powerful FLOW-3D numerical model was used after its calibration. The results indicated that in both conditions, with and without blockage, the maximum scour depth significantly affected by the changes in flow intensity and tailwater depth. An increase in flow intensity leads to an increase in scour depth. In unblocked conditions, there is a critical relative tailwater depth for each specified flow intensity, below which scour depth decreases with increasing tailwater depth, and above which it increases. The laboratory results showed that for a fixed tailwater depth, with an increase in flow intensity, the location of maximum scour depth moved closer to the end of the culvert outlet. The blockage at the inlet section on culvert conduit, with blockage percentages of 20% and 32%, significantly affected the erosion and turbulence of the flow downstream. Compared to the unblocked condition, the presence of the blockage created turbulence in the flow, resulting in a significant drop in flow energy, which decreased the scour depth. However, as the tailwater depth increases, the impact of blockage on scour diminishes due to reduced turbulence in the channel. Given the great importance of water structures, especially culverts, in conveying flood, it is necessary for the designer to pay special attention to the issue of downstream scour when designing the culvert, because the poor performance of the culvert in conveying water during a flood can directly target the health of human communities living downstream and the efficiency of communication infrastructure. Acknowledgment We would like to thank the respected professors of the Department of Water Science and Engineering, Razi University, who prepared the necessary laboratory equipment for this research. | ||
| کلیدواژه‌ها [English] | ||
| Scour, Inlet blockage, Laboratory investigation, Culvert, Numerical Model | ||
| مراجع | ||
|
Abt, S. R., Ruff, J. F. & Doehring, F. K. (1985). Culvert Slope Effects on Outlet Scour. J. Hydraul. Eng.111,1363-1367. Abt, S. R., Ruff, J. F., Doehring, F. K. & Donnell, C. A. (1987). Influence of Culvert Shape on Outlet Scour. J. Hydraul. Eng, 113, 393–400. Abt, S. R., Thompson, P. L. & Lewis, T. M. (1996). Enhancement of the Culvert Outlet Scour Estimation Equations. Journal of the Transportation Research Board. 1523(1), 178-185. Abida, H. & Townsend, R. (1991). Local scour downstream of box-culvert outlets, Journal of Irrigation and Drainage Engineering 118(6): 1001-1003. Amini, A. & Solaimani, N. (2018). The Effects of Uniform and Nonuniform Pile Spacing Variations on Local Scour at Pile Groups. Marine Georesources and Geotechnology 36(7): 861–866. Ahmed, K. O., Amini, A., Bahrami, J., Kavianpour, M. R. & Hawez, D. M. (2021). Numerical modeling of depth and location of scour at culvert outlets under unsteady flow conditions. Journal of Pipeline Systems Engineering and Practice, 12(4), 04021040. Ahmed, K. O., Nariman, N., Hawez, D. M., Kisi, O. & Amini, A. (2023). Predicting and Optimizing the Influenced Parameters for Culvert Outlet Scouring Utilizing Coupled FLOW 3D-Surrogate Modeling. Iranian Journal of Science and Technology, Transactions of Civil Engineering, 47(3), 1763-1776. Ahmed, K. O., Kavianpour, M. R., Amini, A. & Aminpour, Y. (2024). Numerical modelling of downstream scour in circular culverts: Impact of inlet blockages and variable flow conditions. PLoS ONE 19(10): e0312501. Bohan, J. (1970). Erosion and Riprap Requeriments at Culvert and Storm-Drain Outlets, Technical Report, U. S. Army Engineer Waterways Experiment Station, Vicksburg, Mississippi. Chen, Y. H. (1970). Scour at Outlets of Box Culverts, Master's thesis, Colorado State University. Day, R., Liriano, S. L. & White, W. R. (2001). Effect of tailwater depth and model scale on scour at culvert outlets, in: Proceedings of the ICE - Water and Maritime Engineering 148(3): 189-198. Emami, S. & Schleiss, A. J. (2006). Design of erosion protection at diversion tunnel outlets with concrete prisms, Canadian Journal of Civil Engineering 33: 81-92. Elsebaie, H. I. (2013). an experimental study of local scour around circular bridge pier in sand soil. Int. J. Civ. Environ. Eng.13, 23–28. Galán, Á. & González, J. (2022). Effects of shape, inlet blockage and wing walls on local scour at the outlet of non-submerged culverts: undermining of the embankment. Environ Earth Sci 79, 25. Günal, M., Günal, A.Y. & Osman, K. (2019). Simulation of blockage effects on scouring downstream of box culverts under unsteady flow conditions. International Journal of Environmental Science and Technology. 16, 5305–5310. Iqbal U. & Riaz, M. Z. B. (2024). Blockage at cross-drainage hydraulic structures - Advances, challenges and opportunities. Heliyon. 10(16): e35786. Liriano, S. L., Day, R. & Rodney, W. (2002). Scour at culvert outlets as influenced by the turbulent flow structure, J. Hydraul. 40(3): 367–376. Mendoza, C., Abt, S. R. & Ruff, J. F. (1983). Headwall inuence on scour at culvert outlets, Journal of Hydraulic Engineering 109(7): 1056-1060. Moody, J. A., Smith, J. D. & Ragan, B. W. (2005). Critical shear stress for erosion of cohesive soils subjected to temperatures typical of wildfires, J. Geophys. Res.-Earth, 110, F01004, https://doi.org/10.1029/2004JF000141, 2005. Najafzadeh, M. (2015). Neurofuzzy-Based GMDH-PSO to Predict Maximum Scour Depth at Equilibrium at Culvert Outlets. Journal of Pipeline Systems Engineering and Practice. 7(1), 2016. Najafzadeh, M. & Kargar, A. R. (2019). Gene-expression programming, evolutionary polynomial regression, and model tree to evaluate local scour depth at culvert outlets. J Pipeline Syst Eng Pract 10(3): 04019013 Nohani, E. & Heidarnejad, M. (2014). Experimental Investigation of the Effect of Flow Angle of Attack on the Rate of Scour around the Slotted Bridge Pier at Different Levels of River Bend. International Journal for Research in Applied Science and Engineering Technology (IJRASET), 2(12). Opie, T. R. (1967). Scour at Culvert Outlets, Ph.D. thesis, Colorado State University. Rigby, E. H. & Barthelmess, A. J. (2011). Culvert Blockage Mechanisms and Their Impact on Flood Behaviour: Are All Blockages Created Equal,” in 34th World Congress of the International Association for Hydro-Environment Research and Engineering, Engineers Australia, Brisbane, Australia. 380-387. Ruff, J. F., Abt, S. R., Mendoza, C., Shaikh, A. & Kloberdanz, R. (1982). Scour at Culvert Outlets in Mixed Bed Materials, Technical Report, U.S. Department of Trans portation. Federal Highway Administration. Sorourian, S., Keshavarzi, A., Ball, J. & Samali, B. (2014). Blockage effects on scouring downstream of box culverts under unsteady flow. Australasian Journal of Water Resources, 18(2): 180-190. Sorourian, S., Keshavarzi, A. & Ball, J. E. (2015). Scour at partially blocked box-culverts under steady flow. Proceedings of the Institution of Civil Engineers: Water Management, 169(6): 247-259. Taha, N., El-Feky, M. M., El-Saiad, A. A. & Fathy, I. (2020). Numerical investigation of scour characteristics downstream of blocked culverts. Alex Eng J 59:3503–3513. Tien Bui, D., Shirzadi, A., Amini, A., Shahabi, H., Al-Ansari, N., Hamidi, S., Singh, S.K., Thai Pham, B., Ahmad, B.B. & Ghazvinei, P. T. (2020). A Hybrid Intelligence Approach to Enhance the Prediction Accuracy of Local Scour Depth at Complex Bridge Piers. Sustainability. 12(3): 1063. Valizadeh, R., Arman, A. & Ghobadian, R. (2024). Controlling the local scouring of the bottom of the protective inclined apron in a 90- degree mild bend using a numerical model, DOI:10.1016/j.oceaneng.2024.118177. Zhang, R. & Wu, P. (2019). The investigation of shape factors in determining scour depth at culvert outlets, ISH Journal of Hydraulic Engineering, DOI: 10.1080/09715010.2019.1611492. | ||
|
آمار تعداد مشاهده مقاله: 10 تعداد دریافت فایل اصل مقاله: 18 |
||